Home >

How To Make Model Shoe Upper

2008/8/14 14:08:00 41779

The shoe pattern is taken from the surface area of shoe last, and different shoe last need to be made of different shoes by different models. The shoe making industry has been evolving continuously, and the methods of making templates are different from each other, because they are different from each other. They are easy to understand, easy to learn, and have the right way to use (less accuracy and serious discrepancy).

1. Half panel production:

1. use stickers to overlay the outside side of the last table (over the outer surface of the last table).

 

2. remove the excess stickers from last bottom and last peak.

 

3. draw the center line and the middle line of the heel, then remove the center line and the middle line of the heel to distinguish the inner part of the outside part of the last table, so that the sticker can cover the part of the last part, and meet the requirement of 1/2 (half) of the last surface area.

 

4. tear off the stickers that cover the last table 1/2, and paste them on the white paper.

 

The 5. is cut off from the edge of the sticker, making it a cardboard with the shape of the last (half face) and a sticker. It can be duplicated (copied) as a reserve half face board with the last shoe type.

 

Two. Half panel drawing


1. draw the shoe line to make the actual application (material) area of a shoe upper half face with the center line, the rear middle line and the last bottom line (middle bottom line).

 

2. shoe types are divided into bandage and non bandage styles according to their needs. They have different functional requirements for different openings. According to the different functions of shoes, the "opening points" are marked.

 

3. according to the shoe type, draw the half line of the half panel area, such as tongue, front, back, waist, neckline, shoe eye, reinforcing piece, back cover, and so on.


 

Three. Half plane panels are decomposed into decomposed pieces.


The 1. half plane panel decomposes most of the decomposed pieces.

 

2. pick up the decomposed pieces that span the center line and heel line, and wait for the next processing. The other decomposed pieces, according to the joint demand, add the splice, folding position, note and so on. The decomposed pieces of different assembled shoe upper can be used to make chopping knife samples.

 

Four. The whole chip is made from the decomposed chip across the centerline.


1. front, front, back, cover, shoe eye, etc., which belong to the centerline of the decomposed section, should be made by using the method of "median line straightening".

 

The 2. rear piece, the rear contact piece, the splice piece, the rear decoration piece, the reinforcing piece, belongs to the decomposition piece which crosses the rear middle line, and can make use of the "lifting and warping" method and the "middle line straightening" method to make the whole sample.


Five. Note processing to shoe finish.


According to all kinds of shoe type process, all kinds of pieces need to be treated: save material, joint point line, mark tooth, mark pinhole, incision, chamfering, line groove (ditch), small rise, drop warp, code mark...

 

Six. Internal template production.


In accordance with the above shoe pattern making method, the original shoe upper half panel is made in sequence, and the method is the same.


  • Related reading

Shoes And Clothing Quietly Rising Intelligent

Shoemaking technology
|
2008/8/13 15:02:00
41760

The Shoes That Breathe Will Make The Feet Dull.

Shoemaking technology
|
2008/8/13 15:02:00
41748

Yantai Wanhua Has Developed A New Environment-Friendly Isocyanate Adhesive.

Shoemaking technology
|
2008/8/13 14:55:00
41798

ADI Intelligent Running Shoes 1.1 Upgraded Version Debut

Shoemaking technology
|
2008/8/13 14:54:00
41813

Accelerate The Development And Development Of Special Fibers Worldwide

Shoemaking technology
|
2008/8/13 14:54:00
41803
Read the next article

Plane Design Goes Out Of Chaos

Today, one thing is certain that the field of design is expanding, which is a world that needs to be designed. Despite the latest statistics, there are more than 700 teaching institutes in China, and they are still increasing. The number of schooling is multiplying. This makes the design education lacking in Teachers' quality and quality even more difficult to cope with.